Three-Phase & Single-Phase Voltage Drop Calculator (NEC / IEC)
Evaluate true AC impedance voltage drop across 75°C copper or aluminum feeders in feet or meters against NEC 210.19 (<=3% branch / <=5% total) limits.
Why NEC Chapter 9 Table 9 AC Impedance Beats Simplified K-Factor Formulas
Many basic wire calculators rely on DC circular-mil approximations (Vd = 2·K·I·L / CM) that ignore skin effect, magnetic conduit eddy losses, and inductive reactance (X_L). On conductors 1/0 AWG (50 mm²) and larger feeding induction motors or VFDs at 0.80–0.85 power factor, inductive reactance in steel conduit contributes 25% to 55% of total voltage drop.
kVACalc models effective AC impedance using NEC Chapter 9 Table 9 values at 75°C in steel raceway: Z_eff = R_AC·cos(φ) + X_L·sin(φ), multiplied by √3 (1.732) for balanced three-phase runs or 2 for single-phase two-wire circuits. You also get an automatic recommendation for the smallest conductor that simultaneously satisfies thermal ampacity and the 3% branch drop ceiling.
NEC 210.19, IEC 60364-5-52, DIN VDE 0100-520 & NBR 5410 Compliance Ceilings
Across North American and international electrical codes—including NEC 210.19(A) Informative Note No. 4 and 215.2(A)(1), Mexican NOM-001-SEDE, IEC 60364-5-52 Table G.52.1, DIN VDE 0100-520, and ABNT NBR 5410—engineering practice limits branch-circuit drop to 3% and combined feeder-plus-branch drop to 5% on public utility supplies.
Keeping steady-state drop below 3% prevents induction motor locked-rotor torque degradation (starting torque scales with the square of terminal voltage, V²), eliminates contactor coil chatter on 120V/230V control circuits, and avoids nuisance DC-bus undervoltage faults on industrial variable frequency drives.
Reference Benchmark & Formula Specification
Deterministic formula: Vd = K × I × L_km × (R_75C·cosφ + X_L·sinφ) [K = √3 for 3Ø, K = 2 for 1Ø]
| Architecture / Standard Tier | Specification | Scope / Operating Range | Reference Benchmark |
|---|---|---|---|
| NEC 210.19 / NOM-001 Branch | Individual Feeder or Branch Run | Max Recommended <= 3.0 % | 14.4 V max @ 480V |
| NEC 215.2 Total System | Feeder + Branch Combined | Max Cumulative <= 5.0 % | 24.0 V max @ 480V |
| IEC 60364-5-52 Lighting | Public LV Supply Lighting | Max Allowed <= 3.0 % | 12.0 V max @ 400V |
| NEC 647.4 Sensitive Equipment | 60/120V Technical Power | Strict Mandatory <= 1.5 % | 2.0 % Combined Max |
Frequently Asked Questions
Should I enter one-way conduit length or round-trip wire length?
Always enter the one-way physical conduit or cable-tray distance from the breaker panel to the load. The formula automatically applies the round-trip factor of 2 for single-phase circuits and √3 (1.732) for balanced three-phase circuits.
Why does aluminum cable require upsizing two AWG gauges vs copper?
AA-8000 series electrical aluminum has roughly 61% of copper's conductivity (~1.64× higher AC resistance per kilometer). Stepping up two AWG trade sizes (for example from 4 AWG copper to 2 AWG aluminum) restores nearly identical voltage drop and 75°C lug ampacity.
Is the NEC 3% voltage drop rule legally mandatory?
In the base NEC 210.19 and 215.2 text, 3%/5% appears as an Informative Note rather than a general mandatory rule—except on fire pumps (NEC 695.7), sensitive electronic power (NEC 647.4), and state energy codes such as ASHRAE 90.1 and California Title 24 where feeder/branch voltage drop limits are strictly enforced.